oltaco · ViezeVingertjes · Jun 26, 2026 · Jun 26, 2026
diff --git a/examples/companion_radio/MyMesh.cpp b/examples/companion_radio/MyMesh.cpp
@@ -882,9 +882,9 @@ MyMesh::MyMesh(mesh::Radio &radio, mesh::RNG &rng, mesh::RTCClock &rtc, SimpleMe
   _prefs.gps_enabled = 0;       // GPS disabled by default
   _prefs.gps_interval = 0;      // No automatic GPS updates by default
   //_prefs.rx_delay_base = 10.0f;  enable once new algo fixed
-#if defined(USE_SX1262) || defined(USE_SX1268)
-#ifdef SX126X_RX_BOOSTED_GAIN
-  _prefs.rx_boosted_gain = SX126X_RX_BOOSTED_GAIN;
+#if defined(USE_SX1262) || defined(USE_SX1268) || defined(USE_LR1110)
+#ifdef RX_BOOSTED_GAIN
+  _prefs.rx_boosted_gain = RX_BOOSTED_GAIN;
 #else
   _prefs.rx_boosted_gain = 1; // enabled by default
 #endif

diff --git a/examples/simple_repeater/MyMesh.cpp b/examples/simple_repeater/MyMesh.cpp
@@ -911,11 +911,11 @@ MyMesh::MyMesh(mesh::MainBoard &board, mesh::Radio &radio, mesh::MillisecondCloc
 
   _prefs.adc_multiplier = 0.0f; // 0.0f means use default board multiplier
 
-#if defined(USE_SX1262) || defined(USE_SX1268)
-#ifdef SX126X_RX_BOOSTED_GAIN
-  _prefs.rx_boosted_gain = SX126X_RX_BOOSTED_GAIN;
+#if defined(USE_SX1262) || defined(USE_SX1268) || defined(USE_LR1110)
+#ifdef RX_BOOSTED_GAIN
+  _prefs.rx_boosted_gain = RX_BOOSTED_GAIN;
 #else
-  _prefs.rx_boosted_gain = 1; // enabled by default;
+  _prefs.rx_boosted_gain = 1; // enabled by default
 #endif
 #endif
   _prefs.radio_fem_rxgain = 1;

diff --git a/src/helpers/CommonCLI.cpp b/src/helpers/CommonCLI.cpp
@@ -573,9 +573,9 @@ void CommonCLI::handleSetCmd(uint32_t sender_timestamp, char* command, char* rep
     strcpy(reply, _prefs->disable_fwd ? "OK - repeat is now OFF" : "OK - repeat is now ON");
   } else if (memcmp(config, "radio.rxgain ", 13) == 0) {
     bool enabled = memcmp(&config[13], "on", 2) == 0;
-    _prefs->rx_boosted_gain = enabled;
-    savePrefs();
     if (_callbacks->setRxBoostedGain(enabled)) {
+      _prefs->rx_boosted_gain = enabled;
+      savePrefs();
       strcpy(reply, "OK");
     } else {
       strcpy(reply, "Error: unsupported");

diff --git a/src/helpers/esp32/ESPNOWRadio.h b/src/helpers/esp32/ESPNOWRadio.h
@@ -38,7 +38,7 @@ class ESPNOWRadio : public mesh::Radio {
    * These two functions do nothing for ESP-NOW, but are needed for the
    * Radio interface.
    */
-  virtual bool setRxBoostedGainMode(bool) { }
+  virtual bool setRxBoostedGainMode(bool) { return false; }
   virtual bool getRxBoostedGainMode() const { return false; }
 
   uint32_t intID();

diff --git a/src/helpers/esp32/TBeamBoard.cpp b/src/helpers/esp32/TBeamBoard.cpp
@@ -312,7 +312,7 @@ bool TBeamBoard::power_init()
 //           P_LORA_BUSY = 32;
 //           RADIO_CLASS = CustomSX1262;
 //           WRAPPER_CLASS = CustomSX1262Wrapper;
-//           SX126X_RX_BOOSTED_GAIN = true;
+//           RX_BOOSTED_GAIN = true;
 //           SX126X_CURRENT_LIMIT = 140;
 //           //delete radio;
 //           radio = NULL;

diff --git a/src/helpers/radiolib/CustomLLCC68.h b/src/helpers/radiolib/CustomLLCC68.h
@@ -62,8 +62,8 @@ class CustomLLCC68 : public LLCC68 {
   #ifdef SX126X_DIO2_AS_RF_SWITCH
       setDio2AsRfSwitch(SX126X_DIO2_AS_RF_SWITCH);
   #endif
-  #ifdef SX126X_RX_BOOSTED_GAIN
-      setRxBoostedGainMode(SX126X_RX_BOOSTED_GAIN);
+  #ifdef RX_BOOSTED_GAIN
+      setRxBoostedGainMode(RX_BOOSTED_GAIN);
   #endif
   #if defined(SX126X_RXEN) || defined(SX126X_TXEN)
     #ifndef SX1262X_RXEN

diff --git a/src/helpers/radiolib/CustomSX1262.h b/src/helpers/radiolib/CustomSX1262.h
@@ -62,8 +62,8 @@ class CustomSX1262 : public SX1262 {
   #ifdef SX126X_DIO2_AS_RF_SWITCH
       setDio2AsRfSwitch(SX126X_DIO2_AS_RF_SWITCH);
   #endif
-  #ifdef SX126X_RX_BOOSTED_GAIN
-      setRxBoostedGainMode(SX126X_RX_BOOSTED_GAIN);
+  #ifdef RX_BOOSTED_GAIN
+      setRxBoostedGainMode(RX_BOOSTED_GAIN);
   #endif
   #if defined(SX126X_RXEN) || defined(SX126X_TXEN)
     #ifndef SX126X_RXEN

diff --git a/src/helpers/radiolib/CustomSX1268.h b/src/helpers/radiolib/CustomSX1268.h
@@ -62,8 +62,8 @@ class CustomSX1268 : public SX1268 {
   #ifdef SX126X_DIO2_AS_RF_SWITCH
       setDio2AsRfSwitch(SX126X_DIO2_AS_RF_SWITCH);
   #endif
-  #ifdef SX126X_RX_BOOSTED_GAIN
-      setRxBoostedGainMode(SX126X_RX_BOOSTED_GAIN);
+  #ifdef RX_BOOSTED_GAIN
+      setRxBoostedGainMode(RX_BOOSTED_GAIN);
   #endif
   #if defined(SX126X_RXEN) || defined(SX126X_TXEN)
     #ifndef SX1262X_RXEN

diff --git a/src/helpers/radiolib/SX126xReset.h b/src/helpers/radiolib/SX126xReset.h
@@ -25,8 +25,8 @@ inline void sx126xResetAGC(SX126x* radio) {
 #ifdef SX126X_DIO2_AS_RF_SWITCH
   radio->setDio2AsRfSwitch(SX126X_DIO2_AS_RF_SWITCH);
 #endif
-#ifdef SX126X_RX_BOOSTED_GAIN
-  radio->setRxBoostedGainMode(SX126X_RX_BOOSTED_GAIN);
+#ifdef RX_BOOSTED_GAIN
+  radio->setRxBoostedGainMode(RX_BOOSTED_GAIN);
 #endif
 #ifdef SX126X_REGISTER_PATCH
   uint8_t r_data = 0;

diff --git a/variants/ebyte_eora_s3/platformio.ini b/variants/ebyte_eora_s3/platformio.ini
@@ -34,7 +34,7 @@ build_flags =
   -D RADIO_CLASS=CustomSX1262
   -D WRAPPER_CLASS=CustomSX1262Wrapper
   -D LORA_TX_POWER=22
-  -D SX126X_RX_BOOSTED_GAIN=1
+  -D RX_BOOSTED_GAIN=1
 build_src_filter = ${esp32_base.build_src_filter}
   +<../variants/ebyte_eora_s3>
 lib_deps =

diff --git a/variants/ebyte_eora_s3/target.cpp b/variants/ebyte_eora_s3/target.cpp
@@ -57,8 +57,8 @@ bool radio_init() {
 #ifdef SX126X_DIO2_AS_RF_SWITCH
   radio.setDio2AsRfSwitch(SX126X_DIO2_AS_RF_SWITCH);
 #endif
-#ifdef SX126X_RX_BOOSTED_GAIN
-  radio.setRxBoostedGainMode(SX126X_RX_BOOSTED_GAIN);
+#ifdef RX_BOOSTED_GAIN
+  radio.setRxBoostedGainMode(RX_BOOSTED_GAIN);
 #endif
 
   return true;  // success

diff --git a/variants/gat562_30s_mesh_kit/platformio.ini b/variants/gat562_30s_mesh_kit/platformio.ini
@@ -17,7 +17,7 @@ build_flags = ${nrf52_base.build_flags}
   -D LORA_TX_POWER=22
   -D SX126X_CURRENT_LIMIT=140
   -D PIN_BUZZER=33
-  -D SX126X_RX_BOOSTED_GAIN=1
+  -D RX_BOOSTED_GAIN=1
   -D SX126X_DIO2_AS_RF_SWITCH=true
 build_src_filter = ${nrf52_base.build_src_filter}
   +<../variants/gat562_30s_mesh_kit>

diff --git a/variants/gat562_mesh_evb_pro/platformio.ini b/variants/gat562_mesh_evb_pro/platformio.ini
@@ -12,7 +12,7 @@ build_flags = ${nrf52_base.build_flags}
   -D WRAPPER_CLASS=CustomSX1262Wrapper
   -D LORA_TX_POWER=22
   -D SX126X_CURRENT_LIMIT=140
-  -D SX126X_RX_BOOSTED_GAIN=1
+  -D RX_BOOSTED_GAIN=1
 build_src_filter = ${nrf52_base.build_src_filter}
   +<../variants/gat562_mesh_evb_pro>
   +<helpers/ui/MomentaryButton.cpp>

diff --git a/variants/gat562_mesh_tracker_pro/platformio.ini b/variants/gat562_mesh_tracker_pro/platformio.ini
@@ -14,7 +14,7 @@ build_flags = ${nrf52_base.build_flags}
   -D WRAPPER_CLASS=CustomSX1262Wrapper
   -D LORA_TX_POWER=22
   -D SX126X_CURRENT_LIMIT=140
-  -D SX126X_RX_BOOSTED_GAIN=1
+  -D RX_BOOSTED_GAIN=1
 build_src_filter = ${nrf52_base.build_src_filter}
   +<../variants/gat562_mesh_tracker_pro>
   +<helpers/ui/SSD1306Display.cpp>

diff --git a/variants/gat562_mesh_watch13/platformio.ini b/variants/gat562_mesh_watch13/platformio.ini
@@ -16,7 +16,7 @@ build_flags = ${nrf52_base.build_flags}
   -D WRAPPER_CLASS=CustomSX1262Wrapper
   -D LORA_TX_POWER=19
   -D SX126X_CURRENT_LIMIT=140
-  -D SX126X_RX_BOOSTED_GAIN=1
+  -D RX_BOOSTED_GAIN=1
   -D QSPIFLASH=1
 build_src_filter = ${nrf52_base.build_src_filter}
   +<../variants/gat562_mesh_watch13>

diff --git a/variants/heltec_ct62/platformio.ini b/variants/heltec_ct62/platformio.ini
@@ -27,7 +27,7 @@ build_flags =
   -D SX126X_DIO2_AS_RF_SWITCH=true
   -D SX126X_DIO3_TCXO_VOLTAGE=1.8
   -D SX126X_CURRENT_LIMIT=140
-  -D SX126X_RX_BOOSTED_GAIN=1
+  -D RX_BOOSTED_GAIN=1
 build_src_filter = ${esp32_base.build_src_filter}
   +<../variants/heltec_ct62>
 

diff --git a/variants/heltec_e213/platformio.ini b/variants/heltec_e213/platformio.ini
@@ -26,7 +26,7 @@ build_flags =
   -D SX126X_DIO2_AS_RF_SWITCH=true
   -D SX126X_DIO3_TCXO_VOLTAGE=1.8
   -D SX126X_CURRENT_LIMIT=140
-  -D SX126X_RX_BOOSTED_GAIN=1
+  -D RX_BOOSTED_GAIN=1
   -D PIN_BOARD_SDA=39
   -D PIN_BOARD_SCL=38
   -D DISP_CS=5

diff --git a/variants/heltec_e290/platformio.ini b/variants/heltec_e290/platformio.ini
@@ -26,7 +26,7 @@ build_flags =
   -D SX126X_DIO2_AS_RF_SWITCH=true
   -D SX126X_DIO3_TCXO_VOLTAGE=1.8
   -D SX126X_CURRENT_LIMIT=140
-  -D SX126X_RX_BOOSTED_GAIN=1
+  -D RX_BOOSTED_GAIN=1
   -D PIN_BOARD_SDA=39
   -D PIN_BOARD_SCL=38
 build_src_filter = ${esp32_base.build_src_filter}

diff --git a/variants/heltec_mesh_solar/platformio.ini b/variants/heltec_mesh_solar/platformio.ini
@@ -12,7 +12,7 @@ build_flags =  ${nrf52_base.build_flags}
   -D WRAPPER_CLASS=CustomSX1262Wrapper
   -D LORA_TX_POWER=22
   -D SX126X_CURRENT_LIMIT=140
-  -D SX126X_RX_BOOSTED_GAIN=1
+  -D RX_BOOSTED_GAIN=1
 build_src_filter = ${nrf52_base.build_src_filter}
   +<helpers/*.cpp>
   +<../variants/heltec_mesh_solar>

diff --git a/variants/heltec_t096/platformio.ini b/variants/heltec_t096/platformio.ini
@@ -28,7 +28,7 @@ build_flags = ${nrf52_base.build_flags}
   -D SX126X_DIO2_AS_RF_SWITCH=true
   -D SX126X_DIO3_TCXO_VOLTAGE=1.8
   -D SX126X_CURRENT_LIMIT=140
-  -D SX126X_RX_BOOSTED_GAIN=1
+  -D RX_BOOSTED_GAIN=1
   -D PIN_VEXT_EN=26   ; Vext is connected to VDD which is also connected to TFT & GPS
   -D PIN_VEXT_EN_ACTIVE=HIGH
   -D PIN_GPS_RX=25

diff --git a/variants/heltec_t1/variant.h b/variants/heltec_t1/variant.h
@@ -92,7 +92,7 @@
 #define SX126X_DIO2_AS_RF_SWITCH true
 #define SX126X_DIO3_TCXO_VOLTAGE 1.8
 #define SX126X_CURRENT_LIMIT    140
-#define SX126X_RX_BOOSTED_GAIN  1
+#define RX_BOOSTED_GAIN  1
 
 #define P_LORA_DIO_1            SX126X_DIO1
 #define P_LORA_NSS              LORA_CS

diff --git a/variants/heltec_t114/platformio.ini b/variants/heltec_t114/platformio.ini
@@ -28,7 +28,7 @@ build_flags = ${nrf52_base.build_flags}
   -D SX126X_DIO2_AS_RF_SWITCH=true
   -D SX126X_DIO3_TCXO_VOLTAGE=1.8
   -D SX126X_CURRENT_LIMIT=140
-  -D SX126X_RX_BOOSTED_GAIN=1
+  -D RX_BOOSTED_GAIN=1
   -D PIN_GPS_RX=39
   -D PIN_GPS_TX=37
   -D PIN_GPS_EN=21

diff --git a/variants/heltec_t190/platformio.ini b/variants/heltec_t190/platformio.ini
@@ -25,7 +25,7 @@ build_flags =
   -D SX126X_DIO2_AS_RF_SWITCH=true
   -D SX126X_DIO3_TCXO_VOLTAGE=1.8
   -D SX126X_CURRENT_LIMIT=140
-  -D SX126X_RX_BOOSTED_GAIN=1
+  -D RX_BOOSTED_GAIN=1
   -D PIN_BOARD_SDA=2
   -D PIN_BOARD_SCL=1
   -D PIN_TFT_SCL=38

diff --git a/variants/heltec_tower_v2/platformio.ini b/variants/heltec_tower_v2/platformio.ini
@@ -14,7 +14,7 @@ build_flags = ${nrf52_base.build_flags}
   -D LORA_TX_POWER=12
   -D MAX_LORA_TX_POWER=22 ; Max SX1262 output -> ~29dBm at antenna
   -D SX126X_CURRENT_LIMIT=140
-  -D SX126X_RX_BOOSTED_GAIN=1
+  -D RX_BOOSTED_GAIN=1
 build_src_filter = ${nrf52_base.build_src_filter}
   +<helpers/*.cpp>
   +<helpers/sensors>

diff --git a/variants/heltec_tracker/platformio.ini b/variants/heltec_tracker/platformio.ini
@@ -41,7 +41,7 @@ build_flags =
   -D SX126X_DIO2_AS_RF_SWITCH=true
   -D SX126X_DIO3_TCXO_VOLTAGE=1.8
   -D SX126X_CURRENT_LIMIT=140
-  -D SX126X_RX_BOOSTED_GAIN=1
+  -D RX_BOOSTED_GAIN=1
 build_src_filter = ${esp32_base.build_src_filter}
   +<../variants/heltec_tracker>
 lib_deps =

diff --git a/variants/heltec_tracker_v2/platformio.ini b/variants/heltec_tracker_v2/platformio.ini
@@ -26,7 +26,7 @@ build_flags =
   -D SX126X_DIO2_AS_RF_SWITCH=true
   -D SX126X_DIO3_TCXO_VOLTAGE=1.8
   -D SX126X_CURRENT_LIMIT=140
-  -D SX126X_RX_BOOSTED_GAIN=1
+  -D RX_BOOSTED_GAIN=1
   -D SX126X_REGISTER_PATCH=1
   -D PIN_BOARD_SDA=6
   -D PIN_BOARD_SCL=17

diff --git a/variants/heltec_v3/platformio.ini b/variants/heltec_v3/platformio.ini
@@ -26,7 +26,7 @@ build_flags =
   -D SX126X_DIO2_AS_RF_SWITCH=true
   -D SX126X_DIO3_TCXO_VOLTAGE=1.8
   -D SX126X_CURRENT_LIMIT=140
-  -D SX126X_RX_BOOSTED_GAIN=1
+  -D RX_BOOSTED_GAIN=1
   -D PIN_GPS_RX=47
   -D PIN_GPS_TX=48
   -D PIN_GPS_EN=26

diff --git a/variants/heltec_v4/platformio.ini b/variants/heltec_v4/platformio.ini
@@ -32,7 +32,7 @@ build_flags =
   -D SX126X_DIO2_AS_RF_SWITCH=true ; GC1109 CTX is controlled by SX1262 DIO2
   -D SX126X_DIO3_TCXO_VOLTAGE=1.8
   -D SX126X_CURRENT_LIMIT=140
-  -D SX126X_RX_BOOSTED_GAIN=1      ; In some cases, commenting this out will improve RX
+  -D RX_BOOSTED_GAIN=1      ; In some cases, commenting this out will improve RX
   -D PIN_GPS_RX=38
   -D PIN_GPS_TX=39
   -D PIN_GPS_RESET=42

diff --git a/variants/heltec_wireless_paper/platformio.ini b/variants/heltec_wireless_paper/platformio.ini
@@ -28,7 +28,7 @@ build_flags =
   -D SX126X_DIO2_AS_RF_SWITCH=true
   -D SX126X_DIO3_TCXO_VOLTAGE=1.8
   -D SX126X_CURRENT_LIMIT=140
-  -D SX126X_RX_BOOSTED_GAIN=1
+  -D RX_BOOSTED_GAIN=1
   -D DISP_CS=4
   -D DISP_BUSY=7
   -D DISP_DC=5

diff --git a/variants/ikoka_handheld_nrf/platformio.ini b/variants/ikoka_handheld_nrf/platformio.ini
@@ -22,7 +22,7 @@ build_flags = ${nrf52_base.build_flags}
   -D SX126X_DIO2_AS_RF_SWITCH=1
   -D SX126X_DIO3_TCXO_VOLTAGE=1.8
   -D SX126X_CURRENT_LIMIT=140
-  -D SX126X_RX_BOOSTED_GAIN=1
+  -D RX_BOOSTED_GAIN=1
 build_src_filter = ${nrf52_base.build_src_filter}
   +<../variants/ikoka_handheld_nrf>
   +<helpers/sensors>

diff --git a/variants/ikoka_nano_nrf/platformio.ini b/variants/ikoka_nano_nrf/platformio.ini
@@ -23,7 +23,7 @@ build_flags = ${nrf52_base.build_flags}
   -D SX126X_DIO2_AS_RF_SWITCH=1
   -D SX126X_DIO3_TCXO_VOLTAGE=1.8
   -D SX126X_CURRENT_LIMIT=140
-  -D SX126X_RX_BOOSTED_GAIN=1
+  -D RX_BOOSTED_GAIN=1
   -D PIN_WIRE_SCL=5
   -D PIN_WIRE_SDA=4
   -UENV_INCLUDE_GPS

diff --git a/variants/ikoka_stick_nrf/platformio.ini b/variants/ikoka_stick_nrf/platformio.ini
@@ -24,7 +24,7 @@ build_flags = ${nrf52_base.build_flags}
   -D SX126X_DIO2_AS_RF_SWITCH=1
   -D SX126X_DIO3_TCXO_VOLTAGE=1.8
   -D SX126X_CURRENT_LIMIT=140
-  -D SX126X_RX_BOOSTED_GAIN=1
+  -D RX_BOOSTED_GAIN=1
   -D PIN_USER_BTN=0
   -D PIN_WIRE_SCL=7
   -D PIN_WIRE_SDA=6

diff --git a/variants/keepteen_lt1/platformio.ini b/variants/keepteen_lt1/platformio.ini
@@ -9,7 +9,7 @@ build_flags = ${nrf52_base.build_flags}
   -D WRAPPER_CLASS=CustomSX1262Wrapper
   -D LORA_TX_POWER=22
   -D SX126X_CURRENT_LIMIT=140
-  -D SX126X_RX_BOOSTED_GAIN=1
+  -D RX_BOOSTED_GAIN=1
   -D PIN_BOARD_SDA=34
   -D PIN_BOARD_SCL=36
   -D ENV_INCLUDE_GPS=1

diff --git a/variants/lilygo_t3s3/platformio.ini b/variants/lilygo_t3s3/platformio.ini
@@ -26,7 +26,7 @@ build_flags =
   -D RADIO_CLASS=CustomSX1262
   -D WRAPPER_CLASS=CustomSX1262Wrapper
   -D LORA_TX_POWER=22
-  -D SX126X_RX_BOOSTED_GAIN=1
+  -D RX_BOOSTED_GAIN=1
 build_src_filter = ${esp32_base.build_src_filter}
   +<../variants/lilygo_t3s3>
 lib_deps =

diff --git a/variants/lilygo_t_impulse_plus/platformio.ini b/variants/lilygo_t_impulse_plus/platformio.ini
@@ -10,7 +10,7 @@ build_flags = ${nrf52_base.build_flags}
   -D WRAPPER_CLASS=CustomSX1262Wrapper
   -D LORA_TX_POWER=22
   -D SX126X_CURRENT_LIMIT=140
-  -D SX126X_RX_BOOSTED_GAIN=1
+  -D RX_BOOSTED_GAIN=1
   -D PIN_USER_BTN=-1
   ; -D PIN_USER_BTN=TTP223_KEY ; leave button disabled until screen implemented
   ; -D USER_BTN_PRESSED=HIGH

diff --git a/variants/lilygo_tbeam_1w/platformio.ini b/variants/lilygo_tbeam_1w/platformio.ini
@@ -26,7 +26,7 @@ build_flags =
   -D SX126X_RXEN=21
   -D SX126X_DIO3_TCXO_VOLTAGE=3.0
   -D SX126X_CURRENT_LIMIT=140
-  -D SX126X_RX_BOOSTED_GAIN=1
+  -D RX_BOOSTED_GAIN=1
 
   ; TX power: 22dBm to SX1262, PA module adds ~10dB for 32dBm total
   -D LORA_TX_POWER=22

diff --git a/variants/lilygo_tbeam_SX1262/platformio.ini b/variants/lilygo_tbeam_SX1262/platformio.ini
@@ -15,7 +15,7 @@ build_flags =
   -D SX126X_DIO2_AS_RF_SWITCH=true
   -D SX126X_DIO3_TCXO_VOLTAGE=1.8
   -D SX126X_CURRENT_LIMIT=140
-  -D SX126X_RX_BOOSTED_GAIN=1
+  -D RX_BOOSTED_GAIN=1
   -D USE_SX1262
   -D RADIO_CLASS=CustomSX1262
   -D WRAPPER_CLASS=CustomSX1262Wrapper

diff --git a/variants/lilygo_tbeam_supreme_SX1262/platformio.ini b/variants/lilygo_tbeam_supreme_SX1262/platformio.ini
@@ -13,7 +13,7 @@ build_flags =
   -D P_LORA_MISO=19
   -D P_LORA_MOSI=27
   -D SX126X_CURRENT_LIMIT=140
-  -D SX126X_RX_BOOSTED_GAIN=1
+  -D RX_BOOSTED_GAIN=1
   -D USE_SX1262
   -D RADIO_CLASS=CustomSX1262
   -D WRAPPER_CLASS=CustomSX1262Wrapper

diff --git a/variants/lilygo_tdeck/platformio.ini b/variants/lilygo_tdeck/platformio.ini
@@ -17,7 +17,7 @@ build_flags =
   -D LORA_TX_POWER=22
   -D SX126X_DIO2_AS_RF_SWITCH=false
   -D SX126X_CURRENT_LIMIT=140
-  -D SX126X_RX_BOOSTED_GAIN=1
+  -D RX_BOOSTED_GAIN=1
   -D SX126X_DIO3_TCXO_VOLTAGE=1.8f
   -D P_LORA_DIO_1=45 ; LORA IRQ pin
   -D ENV_INCLUDE_GPS=1

diff --git a/variants/lilygo_techo/platformio.ini b/variants/lilygo_techo/platformio.ini
@@ -22,7 +22,7 @@ build_flags = ${nrf52_base.build_flags}
   -D SX126X_DIO2_AS_RF_SWITCH=true
   -D SX126X_DIO3_TCXO_VOLTAGE=1.8
   -D SX126X_CURRENT_LIMIT=140
-  -D SX126X_RX_BOOSTED_GAIN=1
+  -D RX_BOOSTED_GAIN=1
   -D P_LORA_TX_LED=LED_GREEN
   -D DISABLE_DIAGNOSTIC_OUTPUT
   -D ENV_INCLUDE_GPS=1

diff --git a/variants/lilygo_techo_card/platformio.ini b/variants/lilygo_techo_card/platformio.ini
@@ -12,7 +12,7 @@ build_flags = ${nrf52_base.build_flags}
   -D WRAPPER_CLASS=CustomSX1262Wrapper
   -D LORA_TX_POWER=22
   -D SX126X_CURRENT_LIMIT=140
-  -D SX126X_RX_BOOSTED_GAIN=1
+  -D RX_BOOSTED_GAIN=1
   -D HAS_NEOPIXEL=1
   -D HAS_TORCH=1
   -D DISABLE_DIAGNOSTIC_OUTPUT